Hutton Close, Crowther Ind Est, Washington, Tyne & Wear NE38 0AH, England
Email: enquiry@isocomoptocouplers.com
- Tel: +44 (0)191 4166546 - Fax: +44 (0)191 4155055
Circuit
and Package
Description
Absolute Maximum Ratings
Truth Table
Recommended Operating Conditions
Electrical
Characteristics
Reliability and Approvals
Similar Optocouplers
Home
Page
Hermetically sealed 8-pin ceramic dual-in-line package
High speed: Typ 10 Mbit/s (75 ns max)
TTL compatible input and output
High common mode rejection
Performance guaranteed over -55°C to +125°C ambient temperature
range.
Withstand test voltage 1500 Vdc
Function compatibility with 6N137 type devices
The CS600 is a single channel device hermetically sealed in an 8-pin ceramic
package. It incorporates a GaAsP LED emitter and high gain integrated photo
detector. The output is an open collector Schottky clamped transistor.
This device is functionally compatible with 6N137 type devices. Surface Mount Option Available.
Military, high reliability system, telephone ring detection, microprocessor system interface, level shifting, digital logic ground isolation, current loop receiver, isolation input line receiver, system test equipment isolation, process control input/output isolation.
Absolute Maximum Ratings | |
| Storage Temperature: Operating Temperature: Lead Solder Temperature: |
-65°C to +150°C -55°C to +125°C 260°C for 10s, 1.6mm below seating plane |
Input Diode | |
| Peak Forward Current: Average Forward Current: Reverse Voltage: Power Dissipation: |
40mA (=< 1ms duration) 20mA 5V 35mW |
Output Detector | |
| Supply Voltage Vcc: Current Io: Collector Power Dissipation: Voltage Vo: |
7V (1 minute max) 25mA 40mW 7V |
Total Package | |
| Power Dissipation: | 350mW |
(L=Low, H=High)
| INPUT | ENABLE | OUTPUT |
| H | H | L |
| L | H | H |
| H | L | H |
| L | L | H |
Note: Enable input can be open circuit for logic high.
| SYMBOL | PARAMETER | MIN | MAX | UNIT |
| IFL | Input Current Low Level | 0 | 250 | µA |
| IFH | Input Current High Level | 6.3 * | 20 | mA |
| VEH | High Level Enable Voltage | 2.0 | VCC | V |
| VEL | Low Level Enable Voltage | 0 | 0.8 | V |
| VCC | Supply Voltage | 4.5 | 5.5 | V |
| N | Fan-out (TTL load) | 6 |
* 6.3mA condition permits at least 20% CTR degradation guardband on initial switching threshold of 5mA or less.
(Ta=-55 to +125°C u.o.s.) *All typical values at Vcc=5V, Ta=25°C
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN | TYP* | MAX | UNIT |
| IOH | High Level Output Current | VCC=5.5V, VO=5.5V, IF=250µA, VE=2.0V | 20 | 250 | µA | |
| VOL | Low Level Output Voltage | VCC=5.5V, IF=5mA, IOL=13mA, VE=2.0V | 0.4 | 0.6 | V | |
| IEH | High Level Enable Current | VCC=5.5V, VE=2.0V | -1.0 | mA | ||
| IEL | Low Level Enable Current | VCC=5.5V, VE=0.5V | -1.6 | mA | ||
| VEH | High Level Enable Voltage | 2.0 | Vcc | V | ||
| VEL | Low Level Enable Voltage | 0.8 | V | |||
| ICCH | High Level Supply Current | VCC=5.5V, IF=0, VE=0.5V | 10 | 15 | mA | |
| ICCL | Low Level Supply Current | VCC=5.5V, IF=10mA, VE=0.5V | 15 | 19 | mA | |
| IIO | I/O Insulation Leakage Current | RH=45%, TA=25°C, t=5s, VIO=1500Vdc | 1.0 | µA | ||
| VF | Input Forward Voltage | IF=10mA, TA=25°C | 1.5 | 1.75 | V | |
| IF=10mA | 1.85 | V | ||||
| VBR | Input Reverse Breakdown | IR=10µA, TA=25°C | 5 | V | ||
| tPLH | Propagation Delay to Logic High Output | CL=15pF, RL=350ohm, IF=7.5mA, TA=25°C | 75 | ns | ||
| tPHL | Propagation Delay to Logic Low Output | ns | ||||
| CTR | Current Transfer Ratio | VO=0.6V, IF=5mA, VCC=5.5V | 300 | % |
As manufacturer of high reliability optocouplers Isocom Ltd's manufacturing
plant at North Shields, England, has site approval to BS9000 (registered number
1294/M) and CECC20000 (registered number M/1084/CECC/UK) issued by the British
Standards Institution.
Together with CECC, BS9000 is a preferred standard for use in European
military projects. Consequently, Isocom Ltd's approved devices are listed in the
CECC "MUAHAG" preferred products list.
The BS9000 approval is also recognised as meeting the equivalent criteria
to those required by BS5750/IS09000/EN29000.
The Company's customers can be assured of our commitment to stringent
quality, reliability and inspection standards, as demonstrated by our existing
approvals. Other customer specific options can also be offered.
Isocom takes great effort to ensure accurate data, but regrettably cannot be held liable for any error on its website. Visit File Lists to confirm old printouts are up-to-date.